SELECTING THE BEST RODS FOR BASS FISHING
Fishing Rod Terms and Parts
This describes how much of the rod deflects (bends) when you put pressure on the tip. A fast action rod will bend in only the top third or less of the blank, a medium or moderate action will bend in the top half or so and a slow action will bend starting in the lower third of the rod. Sometimes slow action rods are termed 'parabolic', meaning the bend of the rod is similar throughout the length. This description is subject to the type of rod you may be talking about at the time; a fast action fly rod or steelhead rod will bend much lower and more easily than a fast action bass rod or offshore rod.
Most bass rod actions are fast to very fast because this action generally provides better sensitivity and faster power for hooksetting. By faster power we mean the rod 'shuts off' faster, or the bend ends higher on the blank, which means you don't have to move the rod as far on the hookset to get into the stiffer part of the blank. Fast action rods are great for most applications where a short to long casting distance is involved and single hooks are the rule, such as worm and jig fishing.
Medium and medium-fast rods will usually provide a little more casting distance and still provide adequate hooksetting power. These actions are often used for applications that involve treble hooks, such as crankbaits and topwater lures or other reaction baits such as spinnerbaits. The 'bite' of a treble hook is not as deep as a big single worm hook and it is easier to tear the hook out of a strong fish, plus the slower action will not pull the lure out of the fish's mouth before it fully engulfs it. The type of lure you use will usually determine the action of the rod you should use.
Often used synonymously with "action", taper describes not only the thickness of the rod but also the thickness of the wall of the blank and where along the blank less material is used allowing more bend. For our purposes taper is the same as action.
This describes the strength of the rod or it's lifting power. When someone says this rod has a lot of backbone, they mean it has a lot of power. Power ratings are usually described as heavy, medium heavy, medium, etc. Power is closely related to the line strength; heavier power rods will handle heavy line weights and lighter powers will be good for light lines. It is fairly important to keep your line test within the limits printed on the rod since a heavy power rod will snap light lines too easily and heavy lines can snap a light rod. Power ratings vary by the type of rod described; a heavy bass rod and a heavy offshore rod will definitely not feel the same. One might be rated for 25lb line and the other for 80lb line.
The type of water you're fishing will help determine the power of the rod you should select. Thick, heavy cover will require a strong rod to get the fish out before it can tie you up. Clear, open water will often require thin, hard to see lines in order to get bit, meaning you will need a lighter power rod.
Related to modulus this is an idea that reflects the ability of the entire rod to flex under load and release the stored energy in the cast. As we will see below, a finished rod may be the result of different layers of different material, all of which contributes to the responsiveness of the rod. One thing is for sure, the lighter the rod, especially the tip, the more responsive it will be. As Gary Loomis puts it, weight is the deterrent to performance. Overall, the higher the modulus the more efficiently it will store and release energy, which gives you the ability to flick an accurate cast on a lower trajectory.
This is the most common material used in building bass rods today and was first introduced in the 70's by Fenwick. These days graphite is produced using extremely high temperatures in a two-part process, one to create tensile strength and one for stiffness. Temperatures sometimes exceed 3000 degrees! Generally the hotter the furnace in each process the more tensile strength and stiffness the fibers have, which means you need less material to build a rod, and the rods you do build can be lighter and more sensitive.
High tensile strength is sometimes called high strain, and the stiffness is known as tensile modulus or just modulus. To build a rod with high modulus and without high tensile strength creates a brittle rod. That's how some brands can advertise high modulus graphite rods with a cheap price; not all the expensive steps in the graphite making process are completed, giving you an inferior rod.
To reach these extreme temperatures costs a lot of money and the best graphite is very expensive. The parallel graphite fibers created by the heating process are then incorporated into sheets with a resin. You can reduce the cost of materials by using more resin and less graphite, but you end up with a softer rod. You'll need to add more material for a stiffer action, resulting in a heavier, less sensitive rod.
Another layer of fibers is laid onto the sheets of graphite fibers and resin perpendicular to the graphite fibers. This second layer, called the scrim, is almost always fiberglass. The exceptions to this rule are the G. Loomis GLX and the St. Croix SC4 graphite, which incorporate carbon or graphite instead of fiberglass, creating a very expensive and rare material.
The best rods get their specific actions by using a variety of materials, and by using layers of different graphite and/or fiberglass. It's not that difficult to produce a graphite rod, and more and more rods are being built offshore, many in huge plants in China. As we've seen, a material can be called graphite but not exhibit the weight, sensitivity, and toughness that characterizes the best rods on the market today.
This material has been used to produce rods since the 50's and has come a long way since then. Glass is noted for soft actions and toughness, and is used to build some great rods. Many anglers prefer glass rods for throwing crankbaits or other applications where a medium to slow action is required. Some rods are built with a combination of graphite and glass, enabling rod designers to produce some great actions.
IM6, IM7, etc.
These are trade names for particular graphite produced by the Hexcel Corporation. These numbers are not industry standards or an indication of quality, especially since other companies use the designations to refer to graphite not made by Hexcel. At best, they allow you to compare the quality of the material used to build different rods by the same manufacturer. You can be confident that the IM7 rod would use better graphite than the IM6 rod if both are made by the same manufacturer. It's more difficult to say the same about rods from two different companies, since they could be made from material from completely different manufacturers.
As stated above, modulus refers to the stiffness of the graphite, not the amount of material used or the number of graphite fibers incorporated into the sheets. Buying a rod based solely on the modulus rating is a mistake because other factors must be considered. For instance, you don't want the stiffest rod for light line techniques or cranking. In addition, other qualities must be incorporated in the graphite itself and the rod must be designed correctly to ensure the best performance and durability of the rod. The other components that go into a quality rod can also add significantly to the cost.
Most of the guides you will find on bass rods today feature a metal frame and a ceramic ring that the line glides on. This ring can vary greatly in price, and one single guide on a spinning rod can cost in excess of $30 or as little as a couple of bucks. Silicon carbide, or SiC, is usually considered the best material today. It offers a super smooth surface for less friction on the line during the cast and the retrieve. Less friction means longer casts and less heat, and heat kills when it comes to fishing lines.
Alconite is another smooth material that is much less expensive than SiC. Hardloy, Hialoy, and aluminum oxide are other ceramic materials that are quite serviceable and are found on most rods on the market today. They are very inexpensive. Some of the newest guides feature Titanium wire. These guides will spring back into place even if they are bent flat. Standard stainless steel guides break instead of bending, necessitating expensive and annoying repairs. Some proprietary guides use a ring of stainless steel instead of ceramic. These rings are not nearly as smooth as the ceramic inserts but are very lightweight, reducing the overall weight of the rod.
A rod with more guides on it will generally cast better and cost more than the same rod with fewer guides. With more guides the rod will bend more consistently throughout its length, allowing it to utilize all the power for longer casts and fighting fish. The Fuji Concept Guide System is the best example of this development on rods today.
You need to have a comfortable and lightweight handle with sufficient grip, even when it's wet, that will transmit the delicate vibrations of a big bass picking your worm, and cork fits the bill perfectly. A nice, new, fresh, clear, high quality cork grip is a beautiful thing! However, the quality of cork varies greatly along with the price. Most rod manufacturers base the grade of cork used in their rods on the overall cost of the rod; you will get the best cork with the most expensive rods.
The reel seat holds the reel on the rod. There isn't much variation in reel seats. Most anglers prefer graphite seats with a cutout that allows you to feel the blank. The cheapest rods will use reel seats that don't have a plastic cushion inside the metal hoods that the feet of the reel fit into. These seats will often rust and stain your reel. They can bind up, too, making it difficult to remove your reel. Cheap rods, particularly those made offshore, will have cardboard spacers between the reel seat and the rod blank that will dampen vibration and can tear easily, especially when it gets wet, allowing the seat and the reel to rotate on the rod; not a good thing!
When you take all these factors into consideration it's easy to see why the best rods cost so much money. This is especially true of modern bass rods, since anglers demand fast, crisp actions, the lightest weight possible, and the ability to take a beating on the deck of your boat, in the rod locker, or in the back of your pickup.
To be sure you're getting the right rod for the technique or techniques you use, you should read the appropriate section on that technique on the Tackle Warehouse website. Then check out the rods and their descriptions on the site, and buy the best rod you can afford based on what you've learned. All the rods featured on Tackle Warehouse are the best in their respective price range so you can't buy a 'bad' rod. For more information on the rod you're interested in, call our toll free number and talk to one of our staff. Most of us fish competitively and have been bass fishing for a long time, so we know the products we sell.
WE NOW OFFER FREE TACKLE WAREHOUSE GIFT CARDS WITH SELECT ORDERS